Innovative health solutionsE N T E R P R I S E S , L L C
8MOXI / SelectAir distributor prior to operating the control unit. Do not alter the plug to fitinto the power outlet. The power supply cord should be
9Section 5 InstallationInstallation - Mattress ReplacementsMattressNote: Make sure that the mattress hose fitting is at the foot end
10 4. Place the ROHO HIGH PROFILE cushion into the HealFloat foot section of the mattress overlay. Note: Refer to the cushion's enclosed
Section 5 Installation4. Ensure the power entry switch is “OFF”.5. Firmlyinsertthepowercordintotheoutletonthecontrolunit(fig.6).6. In
2. Press the firm mattress timer.3. Place the patient on the mattress, centered and in their habitual resting position, i.e. on their back, on their
Section 6 Manual Setup Comfort Level Reference Chart Note: These charts are only a guideline because weight distribution varies from
Note: Before opening, observe what voltage is visible on the red fuse holder through the window on the fuse holder door.4. Carefully remove
FilterThe filter should be inspected and cleaned every month under normal conditions. Inspect filter and clean or replace as necessary. Bariatric pati
Cleaning and Disinfecting Note: The following instructions are intended only as general guidelines. Follow yourfacility’s standard protocol for clean
washing machine should be set at a regular wash, hot water setting.4. Launder the sheet in a normal manner using the regular cycle and hot water
2
18HealFloat feature (HybridSelect only)Refer to the ROHO HIGH PROFILE cushionʼs operating manual for specific cleaning instructions.Control Unit and H
19TroubleshootingProblem/Corrective Action1. Control unit does not function, and power light not illuminated.Ensure the power cord is connected to a f
20Section 9 TroubleshootingCheck hose for crushed or kinked areas, or internal blockages.Remove filter tray and ensure air inlet vent in control unit
21SelectAir Upright ModeThe Upright Mode increases system pressure to compensate for the upright patient.Note: When the patient is sitting up in bed,
22Note: To assist in deflating the mattress, disconnect the hose at the mattress or control unit.Thenpressthe"UprightOn/Off"
23Section 11 SelectAir MaxFigure 17SelectAir Max Upright ModeThe Upright Mode increases system pressure to compensate for the upright patient.Note:
24Figure 19Section 11 SelectAir MaxTo deactivate the Upright Mode, first lower the patient to a lying position. Thenpress the "Upright On/Off&quo
Figure 21LightSection 11 SelectAir MaxTo unlock the control panel, press and hold the “System Lock” button for three (3)seconds. EnsuretheSystem
262. The Pulsate Mode adjusts as follows: Low–20% cycle every 15 minutes Medium–20% cycle every 7 minutes High–20% cycle every minute.3. To
27Section 12 BariSelectFigure 25BariSelectUpright ModeThe Upright Mode increases system pressure to compensate for the upright patient.Note: When th
1ENGLISH Section 1 Introduction 2-3 Section 2 System Components 4-5 Section 3 Safety Precautions 6 Section 4 Important Safeguards 7-8 Sec
28To deactivate the Upright Mode, first lower the patient to a lying position. Thenpress the "Upright" button a second time. Ensure the Upr
29 • To lock the control panel, press the “Lock/Unlock” button. If no patient activity is detected for 60 seconds, the control unit will auto
30Manual Weight Input BariSelectWheninnormaloperatingmode,presstheManualbuttononthekeypad(fig.30).Thecontrolunitwillentermanualwe
31Figure 33Note: To assist in deflating the mattress, disconnect the hose at the mattress or control unit.CPR/Emergency Deflate Importan
32HybridSelectUpright ModeThe Upright Mode increases system pressure to compensate for the upright patient.Note: When the patient is sitting up in be
33Section 14 HybridSelectTo deactivate the Upright Mode, first lower the patient to a lying position.Then press the "Upright On/Off" button
34Light2. Tounlockthecontrolpanel,pressandholdthe“SystemLock”buttonforthree(3) seconds. Ensure the System Lock light extinguishes.
35Select Air System Specifications:SelectAirSelectAirMaxBariSelect(all sizes)HybridSelectMattress System TypeMattressreplacementMattressreplacementMatt
36Pulsation - Continually readjusts system pressure. SelectAir Max & BariSelect -Low-every 15 minutes, Medium-every 7 minutes, High-every minute.
SelectAir 5 Year Product Warranty37Section 15 WarrantyMOXI Enterprises, LLC warrants the SelectAir (Model SASTDPUMP), SelectAirMax (Model SAMAXPUMP),
2IntroductionSelectAir® low air loss mattress systems are pressure relief mattress systems designed for the treatment and/or prevention of pressure ul
1939 South Vandeventer Avenue, Saint Louis, Missouri 63110www.moxiusa.comToll Free: 1.800.942.7678 • Local: 314.771.5222 • Fax: 314.771.5225of North A
3Section 1 IntroductionSymbol LegendAttention- See accompanying instructions for useor information found in this manual or labels on the
4System Components For Mattress Replacement ModelsSection 2 System ComponentsNote: SelectAir and SelectAir Max mattress replacements
5System Components For HybridS elect Mattress Overlay ModelsSection 2 System ComponentsFigure 2MattressOverlayControl Unit with flexible h
6Safety PrecautionsPlease read and thoroughly understand the following safety precautions before using this product.WARNINGS• Explosion risk if used
7Important SafeguardsPlease read and follow the instructions regardingSelectAir mattress and overlay systemsand retain this manual for future referenc
Comments to this Manuals